Transport 1829 · parts and equipment
Interactive 3D viewerFree · name and email required
Bench-build revision: geometry and assembly details updated; physical fit, structural and flight testing remain outstanding.
Quantities are installed unless marked as workshop/fixture. Confirm the exact version, availability and delivered hardware before buying. Earlier generic gear/axle and regulator proposals are superseded below.
| Quantity | Item | Specification | Source |
|---|---|---|---|
| 4 | Motors | Original SunnySky X2820-800 KV; do not substitute V3 mounting dimensions | Manufacturer / specification |
| 4 | Propeller hubs | Ramoser 4508, 8B four-blade hub for a 5 mm shaft | Manufacturer / specification |
| 16 | Propeller blades | Ramoser 200-8, four blades per hub, 200 mm propeller diameter | Manufacturer / specification |
| 4 | ESCs | Skywalker 60A V2, one per motor; isolate all four BEC positive leads from the receiver | Manufacturer / specification |
| 2 | Drive batteries | Gens ace GEA33004S45D, 4S 3300 mAh 45C with Deans connector; matched pair, maximum case 141 × 44 × 33 mm | Manufacturer / specification |
| 8 | Control servos | HS-85MG: two aileron, two flap, elevator, rudder, upper door and payload gate. | Manufacturer / specification |
| 1 | Ramp servo | D954SW with compatible 25T commercial horn at 20 mm radius. | Manufacturer / specification |
| 2 | Standard servos | D645MW for nose steering and cargo latch. | Manufacturer / specification |
| 1 | Receiver kit | AR14410T SPMAR14410T with four included remotes, extensions and soft switch. | Manufacturer / specification, Manufacturer / specification |
| 2 | Receiver regulators | Hobbywing UBEC25A HV30606000; each 55×40.2×17.6 mm, 74 g. Both set 6.0 V. One per 4S propulsion pack. | Manufacturer / specification |
| 4 | Main wheels | DU-BRO275TL; buy two pair packs for four installed main wheels. | Manufacturer / specification |
| 1 | Nose wheel installed | DU-BRO250TL; one installed, normally sold as a pair. | Manufacturer / specification |
| 5 | Wheel axles | 5/32 inch (3.96875 mm) steel; collars/washers; cut after fitting actual wheel and fork stack. | Manufacturer / specification |
| 1 | Nose kingpin | 5 mm steel, suitable bushings/collars and clamped steering arm; final stack measured. | |
| 3 | Door drive shafts | 3 mm steel with 0.4 mm continuous D-flat. Nominal 185 mm ramp, 181 mm upper door and gate; confirm complete stack. | |
| 4 | Latch pins | 3 mm steel plus springs/Bowden cables. Verify minimum 7 mm withdrawal and 6 mm engagement. | |
| 8 | Hatch magnets | 8 ×3 mm axial discs, four attracting pairs. | |
| 1 | Hatch turnbutton fastener | M3 screw about 10 mm, 0.5 mm washer and nyloc; choose actual engaged stack. | |
| 9 | Tail hinges | DU-BRO standard nylon 16 ×28 mm, three per elevator half and three for rudder. | |
| 4 | Battery straps | 20 mm wide, two per pack; two full-area 2.6 mm insulating pads. | |
| 8 | ESC straps | 10 mm wide, two per ESC; 3 mm insulating pads. | |
| 2 | Throttle Y leads | One for inner throttle pair and one for outer pair. | |
| 4 | Sideboard fasteners | M3 bolts, nuts and washers at X240/X340 on each board. | |
| 2 | Eight-branch power collectors | Eight short equal-length output+/− branches per regulator, merged to one IC3 pigtail. Retain every plug. No single servo/Y throat. | Manufacturer / specification |
| 2 | Source-side IC3 pigtails | Spektrum SPMXCA306, 4-inch 13 AWG battery-side connector. Verify mating receiver connector and polarity. | Manufacturer / specification |
| 4 | Regulator straps | 8 mm wide; two per regulator. Use 1.6 mm pads; leave cooling faces exposed. | |
| 12 | Service cover screws | M2×10, 5 mm OD washers, standard M2 nuts in revised ledge pockets. Four per cover. |
For unchanged carbon/wood members, retaining hardware, servo linkage lengths and materials, also use the source cut lists and drawings linked in the build guide. Fit all actual ends before marking rods; do not treat a viewer centerline as a bare rod cut length.