Skiff 170 parts and equipment
Current build guide · Hardware fit record
Interactive 3D viewerFree · name and email required
Print and fit prototype: physical printing, installed hardware and flight validation remain outstanding.
Selected parts are for the documented prototype. Confirm exact version, supplied hardware and current availability before purchase. Manufacturer dimensions are not proof of installed fit. Quantities below are installed quantities; pack contents may include spares.
| Installed quantity | Item | Specification / fit condition | Source |
|---|---|---|---|
| 4 | iFlight XING2 1404 3800 KV motors | Four;1.5 mm prop-shaft variant;19.9 ×18.4 mm,9.1 g. Verify supplied base screw length against actual windings. | Manufacturer 1 |
| 1 | Gemfan Hurricane 3016 propeller set | Two CW and two CCW,1.5 mm center bore;76.49 mm diameter,5.5 mm hub. Retaining screw engagement must be measured. | Manufacturer 1 |
| 1 | Spektrum SPM4650 | SRXL2 DSMX receiver. Power from regulated 5 V, ground to GND, signal to T2. | Manufacturer 1 |
| 1 | Tattu 650 mAh 3S 75C XT30 | TA-75C-650-3S1P-XT30 — 58 ×31 ×16 mm,59 g nominal. Exact motor/3016 current and thrust remain unmeasured. | Manufacturer 1 |
| 1 | Holybro Kakute H7 Mini v1.5 | 11082 — SKU11082;31 ×30 ×6 mm;20 ×20 M2 mounting; firmware KAKUTEH7MINI; regulated 5 V receiver supply. | Manufacturer 1 |
| 1 | Flywoo GOKU G45M AM32 4-in-1 ESC | FW19003228 — FW19003228;3–6S;33 ×30.4 ×6.1 mm;20 ×20 M2 mounting. Wire by verified pad labels; not by assumed connector order. | Manufacturer 1 |
| 16 | M2 ×5 motor base screws | Sixteen;3 mm printed pad leaves nominal 2 mm penetration. Verify actual thread/winding clearance. | |
| 8 | Propeller retaining screws | Eight; correct thread and measured length for the 5.5 mm hub and actual motor. Not interchangeable with base screws. | |
| 4 | M2 ×40 frame/deck through-bolts | Four, with washers and locknuts. Clamp without crushing printed columns. | |
| 1 | M2 soft stack mounting set | Four stack bolts, soft grommets, isolation spacers, nylon washers/nuts. Determine lengths from actual stack and cables. | |
| 2 | Battery straps | Two 10–12 mm straps and 1 mm non-slip insulating pad. | |
| 1 | Electrical consumables | XT30 lead, correctly polarized supplied low-ESR capacitor, signal wire/heatshrink, strain relief, receiver pad, current-limited first-power device, wattmeter and 3S balance charger. |
Workshop equipment
Caliper, gram scale, straightedge/square, suitable hand tools and the printer/material setup listed in the print guide. Powered models also need an appropriate battery charger, voltage/current measurement and radio setup tools. Use matched material bond coupons before structural adhesive assembly.
Installation details
See the current build guide’s interface table for hole patterns, fastener stacks, retention and channel assignments. Retained source cut lists and mechanical inventory remain necessary for the complete structure.
Verified G45M board labels: manufacturer dimensioned board image. Connect G→GND, V→B+,1–4→M1–M4,C→CURRENT,T→R7 optional; verify continuity before power.
